TLP117 2010-04-02 1 toshiba photocoupler gaa ? as led & photo-ic TLP117 pdp (plasma display panel) fa (factory automation) high-speed interface the toshiba TLP117 consists of a gaa ? as light-emitting diode and an integrated high-gain, hi gh-speed photodetector. z inverter logic (totempole output) z package type : mfsop6 z guaranteed performance over temperature : -40 to 105c z power supply voltage : 4.5 to 5.5 v z input thresholds current : i fhl =5 ma (max) z propagation delay time (tphl/tplh) : 30 ns (max) at vl=0 v z 20 ns (max) at vl=1.1 v z switching speed : 50 mbd (typ.) z common mode transient immunity : 10 kv/ s (min) z isolation voltage : 3750 vrms z ul recognized : ul1577,file no.e67349 z c-ul recognized: csa component acceptance service no. 5a, file no.e67349 truth table pin configuration (top view) input led m1 m2 output h on off on l l off on off h schematic toshiba 11-4c2 weight: 0.09 g (typ.) 1:anode 3:cathode 4:gnd 5: v o 6: v cc 0.1 f bypass capacitor must be connected between pins 6 and 4 1 3 5 6 v cc gnd shield 4 vf v cc v o gnd i cc i o 6 5 4 shield 3- 1+ i f m1 m2 unit: mm free datasheet http:///
TLP117 2010-04-02 2 absolute maximum ratings (ta=25c) characteristic symbol rating unit forward current i f 25 ma forward current derating (ta 85 c) if/ ta - 0 . 7 m a / c peak transient forward current (note 1) i fpt 1 a led reverse voltage v r 6 v output current i o 10 ma output voltage v o 6 v supply voltage v cc 6 v detector output power dissipation p o 40 mw operating temperature range t opr -40 to 105 c storage temperature range t stg -55 to 125 c lead solder temperature(10s) t sol 260 c isolation voltage (ac,1min.,r.h. 60%,ta=25 c) (note 2) bvs 3750 vrms note: using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operat ing temperature/current/voltage, etc. ) are within the absolute maximum ratings. please design the appropriate reliability upon reviewing the toshiba semiconductor reliability handbook (?handling precautions?/?derating concept and methods?) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). note 1: pulse width pw 1 s,300 pps. note 2: this device is regarded as a two-terminal devi ce: pins 1 and 3 are shorted together, and pins 4,5 and 6 are shorted together. recommended operating conditions characteristic symbol min typ. max unit input current , on i f(on) 10 ? 16 ma input voltage , off v f(off) 0 ? 1.0 v supply voltage(*) (note 3) v cc 4.5 5.0 5.5 v * this item denotes operating ranges, not m eaning of recommended operating conditions. note : recommended operating conditions are given as a design guideline to obtain expected performance of the device. additionally, each item is an independent guide line respectively. in developing designs using this product, please confirm specified characteristics shown in this document. note 3 : the detector of this product requires a power supply voltage ( v cc ) of 4.5 v or higher for stable operation. if v cc is lower than this value, i cc may increase or the output may be unstable. be sure to use the product after checking the supply current, and the oper ation of a power-on/-off. free datasheet http:///
TLP117 2010-04-02 3 electrical characteristics (unless otherwise specified, ta=-40 to 105 c, v cc =4.5 to 5.5v ) characteristic symbol te s t circuit conditions min typ. max unit input forward voltage v f ? i f =10 ma , ta=25 c 1.45 1.6 1.85 v temperature coefficient of forward voltage v f / ta ? i f =10 ma ? -2.0 ? mv/ c input reverse current i r ? v r =5 v,ta=25 c ? ? 10 a input capacitance c t ? v=0,f=1 mhz,ta=25 c ? 60 ? pf ?l? level v ol 1 i ol =4 ma, i f =10 ma ? ? 0.6 v v cc =4.5v 3.9 ? ? output voltage ?h? level v oh 2 i oh =-4ma, v f =1.05v, v cc =5.5v 4.9 ? ? v ?l? level i ccl 3 i f =10 ma ? ? 5.0 ma supply current ?h? level i cch 4 v f =0 v ? ? 5.0 ma input current h l i fhl ? i o =20 a,v o <0.3 v ? ? 5 ma input voltage l h v flh ? i o =-20 a,v o >4.0 v 0.8 ? ? v * all typical values are at ta=25 c unless otherwise specified. isolation characteristics (ta = 25c) characteristic symbol test conditions min typ. max unit capacitance input to output c s v = 0,f = 1 mhz (note 2) D 0.8 D pf isolation resistance r s r.h. 60%,v s = 500 v (note 2) 110 12 10 14 D ? ac,1 minute 3750 D D ac,1 second,in oil D 10000 D v rms isolation voltage bv s dc,1 minute,in oil D 10000 D vdc note 4: a cerami c capacitor (0.1 f) should be connected from pin 6 to pi n 4 to stabilize the operation of the high gain linear amplifier. failure to provide the bypass may impair the switching property. the total lead length between capacitor and coupler should not exceed 1 cm. free datasheet http:///
TLP117 2010-04-02 4 switching characteristics (unless otherwise specified, ta=-40 to 105 c, v cc =4.5 to 5.5v) characteristic symbol te s t circuit conditions min typ. max unit propagation delay time to logic high output tphl v in =0 to 5v ? ? 30 ns propagation delay time to logic low output tplh v in =5 to 0v ? ? 30 ns switching time dispersion between on and off |tphl- tplh| ? ? ? 10 ns output fall time(90-10%) tf v in =0 to 5v ? 3 ? ns output rise time(10-90%) tr 5 v in =5 to 0v r in =360 c in =22pf vl=0v (note 5) ? 2 ? ns propagation delay time to logic high output tphl v in =1.1 to 5v ? ? 20 ns propagation delay time to logic low output tplh v in =5 to 1.1v ? ? 20 ns propagation delay skew tpsk ? ? ? 16 ns switching time dispersion between on and off |tphl- tplh| ? ? 2 8 ns output fall time(90-10%) tf v in =1.1 to 5v ? 3 ? ns output rise time(10-90%) tr v in =5 to 1.1v ? 3 ? ns data rate t 6 ? r in =360 c in =22pf vl=1.1v (note 5) ? 50 ? mbd common mode transient immunity at high level output cm h v cm =1000vp-p, ta=25 c i f =0ma,v cc =5v, v o (min)=4v, 10000 ? ? v/ s common mode transient immunity at low level output cm l 7 v cm =1000vp-p, ,ta=25 c i f =10ma,v cc =5v,v o (max)=0.4v -10000 ? ? v/ s *all typical values are at ta=25 c, v cc =5v. note 5 : c l is approximately 15pf which includes probe and jig/stray wiring capacitance. note 6 : this product has an automatic threshold control (atc) circuit in order to reduce input current dependence of its switching time. the atc circuit may not be able to respond accordingly when an input signal is driven after a prolonged absence of signals to the product. as a result, switching operation, pertaini ng to the first pulse of an input signal, could be unstable. theoretically however, stable switching oper ation should be achievable from the second pulse onwards. as such, please check the switch ing operation and take the appropriate measures when designing applications in which this product shall be used. free datasheet http:///
TLP117 2010-04-02 5 test circuit 1 : v ol test circuit 2 : v oh test circuit 3 : i ccl test circuit 4: i cch test circuit 5 : tphl , tplh v cc if v cc gnd shield 0.1 f v ol 1 3 6 5 4 v i ol v cc v cc gnd shield 0.1 f v oh 1 3 6 5 4 v i oh 1 6 v cc gnd shield 3 5 4 i ccl a if v cc v cc gnd shield v cc 1 3 6 5 4 i cch a v cc *cl=15pf 0.1 f r in =360
*cl=15pf v cc gnd shield input monitoring node v in =0 < 5v(p.g) (f=25mhz , duty=50%) cl is capacitance of the probe and jig. (p.g) : pulse generator vo monitoring node c in =22pf 10% 90% tphl tplh 50% v ol v oh tf tr 10% 90% 50% vl=0v gnd tr=4.5ns tf=4.5ns v in v o 0.1 f 0.1 f free datasheet http:///
TLP117 2010-04-02 6 test circuit 6 : tphl , tplh (example for led drive circuit) test circuit 7 : common-mode trans ient immunity test circuit cm l cm h v cm 10% 90% 1000v ?sw b : i f =0ma 0.4v 4v tr tf ?sw a : i f =10ma )( )(800 s t r v h cm = )( )(800 s t f v l cm ?= 0.1 f v o v cc sw if 1 3 6 5 4 v cm b v cc gnd shield a 10% 90% tphl tplh v in v o 50% v ol voh tf tr 10% 90% 50% gnd tf=4.5ns vl=1.1v tr=4.5ns v cc *cl=15pf 0.1 f r in =360 ? *cl=15pf v cc gnd shield input monitoring node v in =1.1? 5v(p.g) (f=25mhz , duty=50%) cl is capacitance of the probe and jig. (p.g) : pulse generator vo monitoring node c in =22pf cin=22pf c in 22 f 0.1 f *cl=15pf v cc gnd vcc gnd p. g 5v f=25mhz shield r in1 =300 ? r in2 =180 ? r in3 =1.6k ? tc7sz08f/fu c in =47pf input monitoring node vo monitoring node v cc cl is capacitance of the probe and jig. (p.g) : pulse generator free datasheet http:///
TLP117 2010-04-02 7 restrictions on product use ? toshiba corporation, and its subsidiaries and affiliates (collect ively ?toshiba?), reserve the right to make changes to the in formation in this document, and related hardware, software a nd systems (collectively ?product?) without notice. ? this document and any information herein may not be reproduc ed without prior written permission from toshiba. even with toshiba?s written permission, reproduc tion is permissible only if reproducti on is without alteration/omission. ? though toshiba works continually to improve product?s quality and reliability, product can malfunction or fail. customers are responsible for complying with safety standards and for prov iding adequate designs and safeguards for their hardware, software and systems which minimize risk and avoid situations in which a ma lfunction or failure of product could cause loss of human life, b odily injury or damage to property, including data loss or corruption. before customers use the product, create designs including the product, or incorporate the product into their own applications, cu stomers must also refer to and comply with (a) the latest versions of all relevant toshiba information, including without limitation, this document, the specifications, the data sheets and application notes for product and the precautions and condi tions set forth in the ?toshiba semiconductor reliability handbook? and (b) the instructions for the application with which the product will be us ed with or for. customers are solely responsible for all aspe cts of their own product design or applications, including but not limited to (a) determining the appropriateness of the use of this product in such design or applications; (b) eval uating and determining the applicability of any info rmation contained in this document, or in c harts, diagrams, programs, algorithms, sample application circuits, or any other referenced documents; and (c) validating all operatin g parameters for such designs and applications. toshiba assumes no liability for customers? product design or applications. ? product is intended for use in general el ectronics applications (e.g., computers, personal equipment, office equipment, measur ing equipment, industrial robots and home electroni cs appliances) or for specif ic applications as expre ssly stated in this document . product is neither intended nor warranted for use in equipment or systems that require extraordinarily high levels of quality a nd/or reliability and/or a malfunction or failure of which may cause loss of human life, bodily injury, serious property damage or se rious public impact (?unintended use?). unintended use includes, without limitation, equipment used in nuclear facilities, equipment used in the aerospace industry, medical equipment, equipment used for automobiles, trains, ships and other transportation, traffic s ignaling equipment, equipment used to control combustions or explosions, safety dev ices, elevators and escalato rs, devices related to el ectric power, and equipment used in finance-related fields. do not use product for unintended use unless specifically permitted in thi s document. ? do not disassemble, analyze, reverse-engineer, alter, modify, translate or copy product, whether in whole or in part. ? product shall not be used for or incorporated into any products or systems whose manufacture, use, or sale is prohibited under any applicable laws or regulations. ? the information contained herein is pres ented only as guidance for product use. no re sponsibility is assumed by toshiba for an y infringement of patents or any other intellectual property rights of third parties that may result from the use of product. no license to any intellectual property right is granted by this document, whether express or implied, by estoppel or otherwise. ? a bsent a written signed agreement, except as provid ed in the relevant terms and conditions of sale for product, and to the maximum extent allowable by law, toshiba (1) assumes no liability whatsoever, including without limitation, indirect, co nsequential, special, or incidental damages or loss, including without limitation, loss of profit s, loss of opportunities, business interruption and loss of data, and (2) disclaims any and all express or implied warranties and conditions related to sale, use of product, or information, including warranties or conditions of merchantability, fitness for a particular purpose, accuracy of information, or noninfringement. ? gaas (gallium arsenide) is used in product. gaas is harmful to humans if consumed or absorbed, whether in the form of dust or vapor. handle with care and do not break, cut, crush, grind, dissolve chemically or otherwise expose gaas in product. ? do not use or otherwise make available product or related so ftware or technology for any military purposes, including without limitation, for the design, development, use, stockpiling or m anufacturing of nuclear, chemical , or biological weapons or missi le technology products (mass destruction w eapons). product and related software and technology may be controlled under the japanese foreign exchange and foreign trade law and the u.s. expor t administration regulations. ex port and re-export of product or related software or technology are strictly prohibited exc ept in compliance with all applicable export laws and regulations. ? please contact your toshiba sales representative for details as to environmental matters such as the rohs compatibility of pro duct. please use product in compliance with all applicable laws and regula tions that regulate the inclusion or use of controlled subs tances, including without limitation, the eu rohs directive. toshiba assumes no liability for damages or losses occurring as a result o f noncompliance with applicable laws and regulations. free datasheet http:///
|
